The Greatest Guide To HP38 powde
The Greatest Guide To HP38 powde
Blog Article
As to get a change in HP-38 or Get 231, I couldn't tell you, but I believe they're typically exactly the same. Every single batch is just a little diverse.
I didn't look at other calibers because I comprehend it is identical, but some below nevertheless feel they're distinctive powders. If what you have got is of the latest acquire, They can be without a doubt the very same.
Yep, when I bought the HP 38 it absolutely was mainly because I read it absolutely was the same as 231. In indisputable fact that Hodgdon had renamed 231 to HP38. But now that I am on the brink of load it and trying out information I see equally detailed on some bullet sites as should they were being two fully distinct powders.
Curt B. states: March two, 2013 at one:twenty pm However I are at this game a long very long time…I’m seeking to open up as many as new Concepts and merchandise. Below’s a person instance….scope mounts and rings. I moved above to the higher finish scopes quite a while back. There isn't a place for the marginal scope despite the applicaton.
Not till now. I have a concentrate on stand for paper targets on my property. I think clays might make a multitude which i dont experience like working with.
I'm not debating which the bullets I'm utilizing could be a small challenging for std 38 Exclusive hundreds.what I'm owning a problem with is info with the powder manufacterer that isn't precise.i dont Use a chrony so i rely upon info i acquire that reveals a specific load recipe and also the velocity it achieves. 158grn lead bullet above three.7 grns velocity at 850fps.that to me looks like a good load to start out a workup.however it doesnt get 850fps and from information previously mentioned is kind of abit decreased.so i adopted right protocall and started reduce than max and realizing they are going to generally be fired in my gp100 I assumed i would've a fantastic accomplishing load.what i obtained was a anemic load that leaded my gun terrible at twenty five rnds.
Medium burn up rate powders choose a few inches of bullet travel to fully melt away up, which boosts velocity significantly. Mid-melt away fee powders are superb for semi-autos because they require an extended stress pulse to hp-38 powder work the slide although developing higher velocity in a lower chamber force.
I referred to as that good enough, appeared like the prudent factor to do. Was my chronograph Completely wrong? Variance in chamber spec, ebook information massive finish, mine at the smaller stop? No technique for realizing. I'd no abnormal force indicators other than the upper than expected velocity.
Posted September 11, 2009 If I'm looking at your post correct, you say hp38 is similar to bullseye??? that remaining reported, The key reason why why its notthat preferred might be (to me) an increased or sharp recoil impulse as opposed to other powders in existence, for that 40 I am applying WST that is softer feeling recoilwise by a mile, for that 9mm slight I am hp-38 powder applying VV 3n37 and w/ the 147 grain its additional of a press than sharp recoil
I haven't study Anybody else come up with a declare that the 9x19 is inherently far more accurate, but, even whether it is, it isn't displaying up on paper with any gun, stock or tailor made on the firing lines I happen to be at.
Bullseye is a tough act to comply with, but I do think it is reasonable to declare that Hodgdon HP-38 has carried out an incredibly admirable work of it which is nipping within the heels of Bullseye.
The insert can make the powder cost improve over quite simple and is incredibly repeatable. I generally verify the powder cost soon after changing the insert and it is always precise to in which I have that insert set. The inserts Price close to $8-9 Every, so a relatively small investment decision per caliber for your added comfort.
Exactly what the alternatively badly labeled ADI chart you cited actually is, is "about the identical burn up amount" data. It's not a "these powders are the exact same" chart. For instance, 700X and WST are claimed for being "equal powders" on that chart from ADI.
Any one at any time use WC867 and/or WC872? I did see where by these are very slow buring powders as a result….significant bullets and total loads.